Red Hat GLOBAL FILE SYSTEM 4.7 Guide de l'utilisateur télécharger pdf (Page 124)

Building an HP SFS client kit manuallyC–6

To create a built kernel tree, perform the following steps:

a. Extract the kernel sources from the src/ directory and put them in the build/linux/

directory, as shown in the following example:

$ mkdir -p build/linux

$ cd src/linux-2.4.21/

$ tar -cpf - ./ | (cd ../../build/linux; tar -xpf -;)

$ cd ../../

b. Apply the Lustre patches, as follows.

i. Extract the Lustre source files, as follows:

$ cd build

$ tar -xzpf ../src/lustre-V1.4.tgz

$ cd ..

ii. Apply the patches listed in the appropriate series file (under the build/lustre-

V1.4/lustre/kernel_patches/series/ directory) to the kernel tree, as follows:

$ for i in $(cat build/lustre-V1.4/lustre/kernel_patches/series/client-

rh-2.4.21-40); do cat

build/lustre-V1.4/lustre/kernel_patches/patches/"$i" | (cd build/linux;

patch -p1); done

c. If any patches are needed for the interconnect, apply them now. The following is an example of

applying the qsnet patches for a Quadrics interconnect:

$ tar -xjf src/qsnetpatches-RedHat-2.4.21-40.EL.qp2.0_hp.tar.bz2

$ cd qsnetpatches-RedHat-2.4.21-40.EL.qp2.0_hp/

$ tar -xjpf qsnetpatches.tar.bz2

$ cd ../

$ cat qsnetpatches-RedHat-2.4.21-40.EL.qp2.0_hp/qsnetpatches/*.patch | (cd

build/linux; patch -p1)

d. Apply the additional required patches to the kernel sources in the same way that you applied

the Lustre patches in Step b of this procedure. See Section 3.2.6 for an example list of additional

patches.

You can find the additional patches in the src directory; you can find the series file (which

lists the patches) in the /mnt/cdrom/client_enabler/src/arch/distro/patches/

directory.

The following is an example of the command that you would use to apply the patches:

$ for i in $(cat

/common/linux/kits/lustre/jimi_clients/current/SFS_V2_2_South_ce_cd/

client_enabler/src/x86_64/RHEL3.0_U7/patches/client_RHEL3_U7_series);

do cat src/"$i" | (cd build/linux; patch -p1); done

e. Regenerate the kernel config file.

• If it is necessary for your system requirements, modify the config file.

•If the config file does not require any customizations for your requirements, enter the

following commands:

$ cd build/linux

$ make oldconfig

$ cd ../../

NOTE: Note that if you are using an x86_64 or i686 system, you must configure the following

setting:

CONFIG_STACK_SIZE_16KB=y

f. Build the kernel and modules.

Depending on your client distribution and architecture, the command line varies. For example,

for i686 (ia32), ia32e (em64t), x86_64 architectures, the command is as follows:

$ make dep clean; make bzImage modules

For ia64 architectures, the command is as follows:

$ make dep clean; make compressed modules

1 2 ... 119 120 121 122 123 124 125 126 127 128 129 ... 133 134

Commentaires sur ces manuels

Pas de commentaire

Red Hat GLOBAL FILE SYSTEM 4.7 Guide de l'utilisateur Page 124

Commentaires sur ces manuels

Produits connexes et manuels pour Manuels des logiciels Red Hat GLOBAL FILE SYSTEM 4.7