Red Hat NETWORK BASIC - USER REFERENCE GUIDE 4.0 Guide de l'utilisateur télécharger pdf (Page 44)

Monitored Network IP

Addresses and Ranges

Specifies the network(s) to be monitored. The default setting is to monitor all IPv4

addresses with the setting of 0.0.0.0/0. This should be changed to only monitor target

networks; otherwise PVS may quickly become overwhelmed. It may contain both IPv4

and IPv6 addresses. Multiple addresses are separated by commas. When monitoring

VLAN networks, a syntax of “vlan ipaddress/subnet” must be used. Example:

192.168.1.0/24,2001:DB8::/64,10.2.3.0/22,vlan 172.16.0.0/16,192.168.3.123/32

Excluded Network IP

Addresses and Ranges

Specifies any network(s) to specifically exclude from PVS monitoring. Specify

networks using CIDR notation. It may contain both IPv4 and IPv6 addresses. Multiple

addresses are separated by commas. When excluding VLAN networks a syntax of

“vlan ipaddress/subnet” must be used. If left blank, no addresses will be

excluded. Example: 192.168.1.0/24,2001:DB8::/64,10.2.3.0/22,vlan

172.16.0.0/16,192.168.3.123/32

PVS Proxy

PVS Proxy Username

This configures the username that SecurityCenter 4.7.x or earlier will use to connect to

the PVS proxy.

PVS Proxy Password

The PVS proxy password is the password that SecurityCenter 4.7.x or earlier will use

in combination with the username to connect to the PVS proxy.

PVS Proxy IP Address

By default, the PVS proxy listens on all IPv4 addresses with the setting of 0.0.0.0. This

may be configured to listen on a specific IPv4 address. The PVS proxy only listens on

the configured address if configured for SecurityCenter 4.7.x or earlier connectivity.

PVS Proxy Port

This setting configures the PVS proxy listening port. By default it is set to 1243 and

may be altered as appropriate for the local environment. The PVS proxy only listens on

the configured port if configured for SecurityCenter 4.7.x or earlier connectivity.

PVS Restart Attempts

The PVS proxy monitors the state of the PVS engine. If the engine stops running, the

proxy will attempt to restart the PVS engine the specified number of times, with the

default setting being 3 and may be set to a value of 1 to 9. Once the restart attempt

limit is reached, it will stop trying for a period of 30 minutes.

PVS Restart Interval

This setting configures the amount of time, in minutes, between PVS restart attempts.

This setting is set to 10 minutes by default and may be set to a value of 1 to 3600.

PVS Web Server

Enable SSL for Web Server

PVS enables SSL protection for connections to the web server by default. Disabling

this option will send traffic between a web browser and PVS unencrypted and is

therefore not recommended. Custom SSL certificates may be installed in the

/opt/pvs/var/pvs-proxy/ssl directory. Changes to this setting require that the

PVS services be stopped and started.

Minimum Password Length

The Minimum Password Length option determines the lowest number of characters

a password may contain. This may be between 5 and 32 characters, with a default

setting of 5.

PVS Web Server Address

By default the PVS web server listens on all available IPv4 and IPv6 addresses

utilizing the setting 0.0.0.0. This may be changed to listen on a specific address or

multiple addresses separated by commas.

PVS Web Server Port

This is the port the PVS web server listens on, which by default is 8835. This may be

altered as appropriate for the local environment.

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 ... 78 79

Commentaires sur ces manuels

Pas de commentaire

Red Hat NETWORK BASIC - USER REFERENCE GUIDE 4.0 Guide de l'utilisateur Page 44

Commentaires sur ces manuels

Produits connexes et manuels pour Logiciel Red Hat NETWORK BASIC - USER REFERENCE GUIDE 4.0