Red Hat Server tc3100 Guide de l'utilisateur Page 139
- Page / 158
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Removal and Replacement 139
Removal and Replacement
5 Rotate the disk system and place it on the back end of the disk system. The
empty disk module slots should be facing up.
6 Align the end cap tabs into the appropriate slots at the top of the disk system.
7 Rotate the end cap down over the base, aligning the small tabs at the top of
the end cap with the end cap slots. Insert and tighten the M5 retaining screws
using the Torx T25 driver. Be sure the retaining screw holes are aligned (see
Figure 67).
- Edition E0902 1
- Format Conventions 2
- Trademark Information 2
- 1 Product Description 11 3
- 2 Installation 35 3
- 3 Configuration 83 4
- 4 Troubleshooting 95 5
- 5 Removal and Replacement 107 5
- 6 Reference 141 6
- Product Description 11
- Features 13
- 14 Product Description 14
- Status Indicators 15
- Power/Standby Switch 16
- High Availability 16
- Clustering (NT) 16
- Upgradability 16
- Environmental Services 17
- Hardware Event Monitoring 17
- Components 18
- BCCs and BCC Filler Panels 19
- 20 Product Description 20
- ■ Locking thumbscrews (E) 20
- ■ Cam levers (F) 20
- Product Description 21 21
- ■ Bus expansion (LVD) 21
- ■ System fault detection 21
- Power Supply/Fan Module 22
- Product Description 23 23
- Topologies 27
- 28 Product Description 28
- Product Description 29 29
- 30 Product Description 30
- Product Description 31 31
- 32 Product Description 32
- Definitions 33
- Ultra160 SCSI 34
- Installation 35
- Preparation 36
- Choosing PDUs 37
- Installing PDUs 39
- 40 Installation 40
- Installation 41 41
- Software Requirements 42
- Auto-Termination 43
- Step 1: Gather Tools 44
- Step 2: Unpack the Product 44
- Installation 45 45
- B Two power cords (8120-6514) 46
- Step 3: Install the device 47
- 48 Installation 48
- Installation 49 49
- ■ Flat-blade screwdriver 49
- ■ T25 nut driver 49
- 50 Installation 50
- Installation 51 51
- 52 Installation 52
- Figure 23) 53
- 54 Installation 54
- Installation 55 55
- 56 Installation 56
- Installation 57 57
- 58 Installation 58
- Installation 59 59
- 60 Installation 60
- Arail tab 60
- B clip nut 60
- Figure 31) 61
- 62 Installation 62
- Installation 63 63
- 64 Installation 64
- Installation 65 65
- 66 Installation 66
- Installation 67 67
- 68 Installation 68
- Installation 69 69
- Install the Disk System 70
- Step 4: Install BCCs 71
- 72 Installation 72
- Installation 73 73
- Step 5: Set DIP Switches 74
- Installation 75 75
- 76 Installation 76
- Installation 77 77
- Step 7: Install Disk Modules 78
- Installation 79 79
- LED (C) should be off 80
- Sample IOSCAN 81
- Where do you go from here? 82
- Configuration 83
- Setting DIP Switches 85
- 86 Configuration 86
- Rationale 87
- Disk Addressing 88
- Disk Slots and Addressing 89
- 90 Configuration 90
- Command View SDM 91
- Supported Operating Systems 92
- Installing CommandView SDM 92
- HP TopTools 93
- 94 Configuration 94
- Overview 96
- HP Command View SDM 100
- TopTools 100
- Status LEDs 101
- Troubleshooting 103
- Isolating Faults 104
- Troubleshooting 105 105
- Removal and Replacement 107
- 108 Removal and Replacement 108
- Removal and Replacement 109 109
- Disk Module 110
- Removal and Replacement 111 111
- 112 Removal and Replacement 112
- Removal and Replacement 113 113
- 114 Removal and Replacement 114
- Windows 2000 115
- Procedure 115
- 116 Removal and Replacement 116
- Removal and Replacement 117 117
- 118 Removal and Replacement 118
- 120 Removal and Replacement 120
- Removal and Replacement 121 121
- BCC Filler Panel 122
- Power Supply 123
- 124 Removal and Replacement 124
- Disk System 125
- 126 Removal and Replacement 126
- Removal and Replacement 127 127
- Top Cover (HP-Qualified Only) 128
- Removal and Replacement 129 129
- Midplane (HP-Qualified Only) 130
- Removal and Replacement 131 131
- Powering Down the Disk System 133
- Figure 62 135
- 136 Removal and Replacement 136
- Removal and Replacement 137 137
- 138 Removal and Replacement 138
- Removal and Replacement 139 139
- Reference 141
- Upgrade Products 142
- PDU/PDRU Products 143
- Replaceable Parts 144
- Specifications 145
- AC Power Input 146
- DC Power Output 146
- Heat Output 146
- Environment 146
- Acoustics 147
- Safety Certifications 147
- EMC Compliance 147
- Regulatory Statements 148
- Reference 149 149
- E. VCCI Statement (Japan) 150
- G. Declaration of Conformity 151
- Product Web Site 152
- Related Documents 152
Produits connexes et manuels pour Processeurs Red Hat Server tc3100
(60 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels